Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Keypad & Intercom Repair: The Winchester Owner’s Guide
We repair and replace Ghost Controls keypads and intercom units in Winchester, and most installed jobs land between $185 and $420 depending on whether we’re swapping the keypad, the intercom, or both, and whether the low-voltage wiring needs attention. Same-day service is available in Winchester on most weekdays when you call before early afternoon. The part usually announces itself before it dies: a keypad that takes three or four presses to register, an intercom that only transmits one direction, or a code that works at the pedestrian gate but not the vehicle gate. If any of that sounds familiar, you’re likely looking at a failing keypad membrane, a corroded terminal block, or a failed voice module, not a gate motor problem.
Which Ghost Controls Models This Applies To
Ghost Controls builds keypads and intercoms for its own residential swing and slide operators, and the accessory line is narrower than people expect. The wireless keypad (their model family with the 25-code capacity) fits any Ghost Controls operator that has a compatible receiver board, but the older wired keypads do not swap directly into the newer wireless-ready control boxes without the right receiver module. When we arrive, we identify your operator first: the model plate is on the control box cover or the back of the arm housing, and the board revision inside the box matters more than the sticker. A keypad that worked on a 2020 board can lose compatibility on a 2023 revision because the receiver pinout changed.
On the OEM-versus-aftermarket question, we lean OEM for Ghost Controls keypads and intercoms when the part is available, because the mounting footprint and the low-voltage connector are proprietary. Aftermarket universal keypads exist and some work fine, but they rarely match the Ghost Controls faceplate cutout, and we’ve seen homeowners drill out a housing to make one fit, which ruins the weather seal. If OEM isn’t available, we’ll tell you in writing and name the aftermarket unit we’re using before we install it. Vance Gate Repair Winchester is an independent service provider and is not affiliated with Ghost Controls.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Keypad & Intercom Repair Is Failing

Here’s what we actually find when we test keypads and intercoms in Winchester:
- Keypad accepts the code but the gate doesn’t move. The keypad is transmitting, but the receiver inside the control box isn’t hearing it. Usually a failed receiver module or a loose terminal at the board, not a dead keypad.
- Keys require a hard press, or one column of numbers stops working. The membrane has worn through under the most-used digits. Common in keypads that have been in direct summer sun, which is most of them in Winchester.
- Intercom transmits one way only, or sounds garbled. The speaker or microphone element has failed, or moisture has reached the circuit board. Desert temperature swings crack the sealant over time.
- Intermittent operation after rain or an irrigation cycle. Water is getting into the housing through a failed gasket or a stripped screw hole. It’ll work dry and fail wet until the seal is replaced.
- Nothing lights up at all. Power isn’t reaching the unit. That could be the keypad, the low-voltage run, or the transformer feeding it, and we test all three before quoting a part.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Ghost Controls keypad and intercom work in Winchester runs roughly as follows, and every number below is written on your quote before we start:
| Job | Typical installed range |
|---|---|
| Keypad replacement (OEM Ghost Controls, standard mount) | $185 – $280 |
| Intercom unit replacement (single-unit) | $240 – $360 |
| Keypad plus intercom, same visit | $380 – $480 |
| Low-voltage wiring repair or re-termination | $85 – $180 additional |
| Receiver module replacement inside control box | $95 – $165 additional |
What drives the range: whether the existing mount is reusable, whether the wire run is intact or needs a new pull, and OEM versus aftermarket part. Every job includes removal and disposal of the old unit, programming your codes, a full test of every code and intercom channel, and a photographed record of the terminal connections and settings we left behind. The 365-Day Done Right Promise covers the install, so if the keypad fails inside that window, we come back and make it right at no additional charge.
DIY or Call Us?

You can safely check a few things yourself: confirm the transformer is outputting power, look for visible corrosion or water inside the keypad housing, and check the wire connection at the control box terminals. What goes wrong beyond that is usually the low-voltage run. Ghost Controls keypads and intercoms run on low voltage, but the unit still connects into a live control box next to a 12-volt DC operator with a battery, and we’ve seen homeowners cross a wire and fry a receiver board or, worse, a control board. A crossed terminal on a unit wired into a 12-volt system won’t shock you, but it can short the operator and leave the gate stuck open, which is a security problem in Winchester. We also test the low-voltage run before we install, so we’re not selling you a keypad when the actual fault is the wire. Call (866) 983-9213 and we’ll tell you honestly whether this is a part or a wiring issue.
FAQs
How long does a Ghost Controls keypad or intercom last in Winchester? Expect seven to twelve years on a keypad and six to ten on an intercom, shorter if the unit sits in full afternoon sun. The desert heat is harder on the membrane and the sealant than the cold is, and we see more sun-related keypad failures in Winchester than anything else.
Can you repair the keypad instead of replacing it? Sometimes. A corroded terminal or a failed receiver module can be fixed without a new keypad, and we’ll tell you which one you’ve got after testing. A worn membrane cannot be repaired and the keypad has to be replaced.
How long does the swap take? Most keypad and intercom replacements are done in 45 minutes to an hour and a half, including programming and testing every code. If the low-voltage run needs repair, plan on two to three hours.
How do you source the part? We match the exact Ghost Controls model and board revision on your operator, order the OEM part where it’s available, and name the aftermarket unit in writing if OEM is out of stock. You’ll see the part number on the quote before we start.
If your Ghost Controls keypad or intercom is failing, call (866) 983-9213 for a free estimate. We’ll test the unit, tell you what actually failed, and hand you a written price before we pick up a tool. A live person answers 24 hours a day, no callback queue.
Written by the team at Vance Gate Repair Winchester, serving Winchester and nearby areas.