A Vance company - serving Winchester, NV

Ghost Controls Gate Parts & Welding in Winchester, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Gate Parts & Welding in Winchester: What to Know First

We supply and fit Ghost Controls gate parts and handle the welding side of the same job in Winchester, usually finishing hinge, roller, latch and rail repairs on the same visit once the bracket or post is sound. When welding or concrete work is needed, we photograph the failure, set a written price, and schedule the return trip within days. As an independent Ghost Controls service provider, we work on the brand without any manufacturer authorization, and we’ll tell you plainly whether a part, a weld, or a whole new arm assembly is the honest answer before anyone picks up a tool.

Call (866) 983-9213

This page is for Winchester homeowners who already own a Ghost Controls system and want the price on the page rather than a callback. Call (866) 983-9213 and a live person answers, day or night.

Key Takeaways

  • Ghost Controls residential swing openers (the TDSO and AXO lines especially) carry their load through the gate hinge and post, so motor faults often trace back to a sagging hinge or a footing that moved.
  • We weld, re-hang, re-set posts and replace rollers, latches and locks, not just the opener itself.
  • Written price before work starts. Photo record when we leave. 365-Day Done Right Promise on the repair.

How Ghost Controls Products Fail – and How We Fix Them

Most Ghost Controls calls we run in Winchester are not electronics problems. They’re mechanical failures the opener has been quietly compensating for, and the arm or the control board finally takes the blame. Five patterns show up again and again:

  • Drooping gate hangs the arm on a TDSO dual-swing system. A gate that has settled a quarter-inch at the latch side puts side load on the operator arm, which the Ghost Controls controller reads as a stall and shuts down mid-travel. We re-hang the hinge, correct the sag, and weld a reinforcement plate if the hinge post is thin-wall steel. The motor usually needs nothing.
  • Loosened post footing on an AXO single-swing install. A post that has tipped out of plumb by even a degree over a season throws the arm geometry off and the gate drifts at the end of its run. We reset or sister the post, then re-measure the arm mounting height and re-set it to the manufacturer’s spec rather than bending the bracket to compensate.
  • Seized or flat-spotted gate rollers. Rollers that stop turning drag the gate along the track and load the opener every cycle. We replace them with matched-diameter rollers. Mismatched rollers (one new, one worn) are one of the most common causes of a gate that operator-reverses for no obvious reason.
  • Latch and lock misalignment after a season of settling. Ghost Controls arms close the gate precisely; if the latch has shifted, the arm keeps pushing and the control board logs a fault. We realign or replace the latch and weld the strike plate if the gate box has opened up.
  • Cracked rail or hinge-leaf welds on older steel gates. Factory spot welds at the hinge leaf fatigue where the gate flexes. We cut out the cracked weld, grind it back, and re-weld with full penetration, then re-check the arm travel from the closed limit so nothing binds.

One detail Ghost Controls owners rarely get from the manual: on the TDSO and AXO series, the arm pivot bracket bolts to the gate with hardware that loosens under the gate’s own vibration over months. A bracket that’s a turn loose will imitate a failing control board. We check bracket torque on every Ghost Controls service call and record the reading.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Our Ghost Controls Gate Parts & Welding Process

professional gate repair service
Our Ghost Controls Gate Parts & Welding Process
  1. 1
    Phone diagnosis. A live person answers 24/7 – no voicemail, no callback window. We ask which Ghost Controls model, what the gate does at open and close, and whether the arm stalls, reverses or won’t latch.
  2. 2
    On-site inspection. We test the arm travel, measure post plumb and gate sag, and check hinge, roller, latch and bracket torque. Photos of what we find before we quote.
  3. 3
    Parts decision in writing. Where a Ghost Controls OEM part is the right call (control board, arm, limit hardware) we say so; where a quality aftermarket hinge, roller or latch does the job for less, we say that too. The flat price is written and handed to you before any work starts – Haven Standard Clause 1, every time.
  4. 4
    The repair. Welding, hinge replacement, post reset, roller and latch swap, arm re-mount. On-site welding is done with the gate isolated and the operator powered down.
  5. 5
    Test and photo record. We cycle the gate through open, close and obstruction-reverse, recheck limit positions, and photograph every adjustment and the installed part number. You get that record before we leave.
  6. 6
    Guarantee. The repair is covered by the 365-Day Done Right Promise – a full year to make it right at no additional charge.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
BeforeBefore
AfterAfter

What Ghost Controls Gate Parts & Welding Costs in Winchester

Job Typical range
Hinge replacement (per hinge, incl. welding) $180 – $340
Gate roller replacement (set) $150 – $280
Latch and lock realignment or replacement $160 – $320
Rail or hinge-leaf weld repair $200 – $450
Post reset or sister weld $350 – $750
Custom welding on a gate box or bracket $300 – $900

What moves the price: whether the post needs concrete work, whether we can weld on-site or have to pull the gate leaf, and whether a Ghost Controls arm or control board is also involved. Every price is quoted and agreed before work starts. Call (866) 983-9213 for an exact quote – estimates are free, including a free second opinion on any written estimate you have from another company.

Why Winchester Homeowners Call Vance Gate Repair Winchester for Ghost Controls Work

Professional welder performing gate hinge repair and metal fabrication services.
Why Winchester Homeowners Call Vance Gate Repair Winchester for Ghost Controls Work

The 365-Day Done Right Promise covers every repair we finish – if it’s not right within a year, we make it right, no argument and no fee. Our technicians have up to 12 years of experience, they’re background-checked, and a live person answers the phone at any hour. Every job leaves a documented photo record of what we found, adjusted and installed, filed with the job and left in your hands. We service nine automation brands, so if the Ghost Controls unit is beyond saving you’ll hear it honestly, and we can work on whatever LiftMaster, Mighty Mule or DoorKing system is already on the property rather than push a replacement. That’s the standard Winchester homeowners come to Vance Gate Repair Winchester for.

Get the price in writing before anything starts.A real person answers, day or night.
Call now

FAQs

Does repairing the gate void my Ghost Controls warranty? Mechanical work on hinges, rollers, latches and welding doesn’t touch the Ghost Controls electronics warranty, and we keep it that way by working the mechanical side first and documenting it. If an OEM part is needed, we fit it so the warranty stays intact. Call (866) 983-9213 to talk through your exact setup.

Can you get Ghost Controls parts in Winchester? Yes – we source OEM control boards, arms and limit hardware, and matched-diameter aftermarket hinges, rollers and latches where they do the job at lower cost. We name the part number and price before ordering. Call (866) 983-9213.

Should I repair my Ghost Controls gate or replace the whole system? Repair is the right answer in most cases – a sagging hinge, a frozen roller or a cracked weld is fixable for a fraction of a new system, and the Ghost Controls motor usually needs nothing. We’ll tell you plainly when parts and labor no longer add up. Call (866) 983-9213 for a free inspection.

How fast can you handle a Ghost Controls gate repair in Winchester? Hinge, roller, latch and weld repairs are usually finished same day, and a live person answers 24/7. Call (866) 983-9213 and we’ll give you a written price before any work begins.

Need Gate Repair help nationwide? Licensed & insured · 30-60 min response · free estimates
Call (866) 983-9213
Local Service Coverage

Request a Free Estimate in Winchester

Tell us what you need - Vance Gate Repair Winchester responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch