Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Repair Before & After in Winchester, NV
Seeing the work speaks louder than any claim we could make. Below are before-and-after write-ups from gate repair jobs around Winchester: what we found, what we adjusted, and what the gate did afterward. Each one follows the same routine – written price agreed first, photo record taken before and after, and a full year to make it right under the 365-Day Done Right Promise.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Recent Transformations
Swing Gate That Stopped Reversing – FAAC Operator Reset in a Sun City Anthem Courtyard
Before
After
Before
AfterThis FAAC swing gate in a Sun City Anthem courtyard kept striking its closed stop, and the homeowner was worried the safety reverse was failing. We checked the photo-eyes first and found the beam misaligned by about two inches after the low winter sun shifted across the driveway. We realigned the mounts, then found the limit switch set past the gate’s true travel – the arm was driving into the hard stop on every close. We reset the limit and re-ran the reverse test with a box in the path. The gate now reverses cleanly on contact, and the homeowner has a photo log of the new switch position.
Sliding Gate That Wouldn’t Close – Roller and Track Repair in Green Valley
Before
After
This sliding gate in Green Valley would travel about halfway and then stall, and the homeowner had been propping it with a patio chair. The track had drifted out of true, and one ground roller had seized from grit that builds up through the dry months around Winchester. We replaced the failed roller set and realigned the track back to level. A gate this heavy was dragging on the operator and had started to chew its own motor; fixing the rail first meant the operator didn’t need replacing. We left a photo of every adjustment and the part numbers fitted.
LiftMaster Opener Caught by Power Surges – Surge and Control Board Replacement in Summerlin


A LiftMaster operator on a Summerlin property had gone dead after a thunderstorm, and the homeowner assumed the whole unit had failed. We opened the housing and traced the fault to a scorched control board – a common outcome when a nearby strike pushes voltage through a gate motor in Winchester’s storm season. We replaced the board rather than the operator, added a surge protection module ahead of it, and tested the full cycle. The gate is running again for a fraction of what a replacement would have cost.
Ghost Controls Opener That Wouldn’t Take the Remote – Receiver and Antenna Fix in Centennial Hills


The homeowner in Centennial Hills had bought new remotes because theirs had “stopped working,” and the new ones wouldn’t pair either. The real fault was a corroded antenna connection on the Ghost Controls receiver – fine dust and heat had worked at the fitting until the signal dropped. We cleaned and reseated the mount, re-paired the existing remotes, and confirmed range from the far end of the driveway. The old remotes still work. We always check the receiver before a customer spends money on parts they may not need.
Wrought-Iron Gate Sagging on Its Hinge – Welding Repair in the Lakes


A wrought-iron pedestrian gate at a Lakes property had dropped until it dragged on the ground, and the cracked weld at the lower hinge had started to split wider. We realigned the hinge, welded the joint back solid, and dressed the repair so it disappears against the frame. The gate swings square and latches the first time. Welding is where we prefer repair – there’s rarely a reason to replace good iron because one joint failed.
Gate Opener That Kept Running at Night – BFT Limit and Timer Set in Peccole Ranch


This BFT operator in Peccole Ranch was cycling on its own at night, and the homeowner had started unplugging it before bed. We traced it to a timer setting left open after a prior adjustment and a limit set just short of true travel, which made the operator keep trying to close a gate that was already shut. We corrected both settings and ran a full open-close test. It’s been quiet overnight since. Every setting change went on the photo record.
Want Results Like These?

If your gate is dragging, stalling, cycling on its own, or hitting its stops, call us at (866) 983-9213. We’ll bring the right parts, write the price before any work begins, and leave a photo record of everything we adjusted. Licensed and insured, with the 365-Day Done Right Promise standing behind every repair in Winchester.
Written by the team at Vance Gate Repair Winchester.
See the difference
Before
After
Before
After
Before
After