Sliding driveway gates
Wrought iron
Wood & steel frame
Farm & ranch
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterDriveway Gate in Winchester, NV
A driveway gate in Winchester, NV is a powered or manual barrier across your vehicle entrance, and most homeowners here need one of three things: a new gate hung and automated, an existing gate that has stopped opening reliably, or a motor and safety system that no longer meets how the gate is actually used. We install and service both swing and slide driveway gates, and we work on whatever motor is already bolted to your property instead of steering you toward a new one. Call (866) 983-9213 and a live person picks up, day or night.
What sets our driveway gate work apart is the paperwork that comes with it. Every visit starts with a written price and ends with a documented photo record: what we found, what we set, what we installed. That habit carried over from commercial access-control work, and it applies whether we’re hanging a new Mighty Mule dual-swing gate on a Paradise Road property or resetting a limit switch on a LiftMaster operator that’s been in service for a decade. This page sits under our broader Gate Installation in Winchester service, which covers the full range of gate types we handle. If you’ve been comparing options, start at our Gate Installation page for the wider picture, then come back here for the driveway-specific details.
When You Need Driveway Gate Service
Driveway gates fail in predictable ways, and the desert climate around Winchester speeds up a few of them. Here’s what usually brings a homeowner to the phone:
- The gate stops mid-travel or reverses on its own. This is almost always a limit-switch or photo-eye problem. A photo-eye is the infrared beam that stops the gate if something crosses the path. In Winchester, blowing dust and fine grit collect on the lenses and misalign the beam by a fraction of an inch, which is enough to trigger a false reversal. We clean, realign and photograph the new position.
- The operator runs but the gate doesn’t move. A stripped drive gear, a slipping chain, or a failed clutch. On older swing operators we often find the arm bracket has fatigued at the weld after years of summer heat cycling. We check the bracket before quoting a motor, because a motor replacement won’t fix a bracket that’s about to let go.
- The gate drags, scrapes, or sags at the latch end. Hinge wear and post settling. Ground movement after a monsoon season is common on properties near the wash corridors, and a sagging gate puts strain on the operator every single cycle.
- You’re adding a gate to a driveway that never had one. New construction, a newly fenced yard, or a property where the old fence-line gate was manual and you want it automated. This is a layout and power question as much as a hardware question, and we map the swing clearance before anything is ordered.
- The motor is loud, hot, or tripping a breaker. Electrical faults on gate operators are a real safety concern, not a nuisance. We treat any breaker-tripping operator as an electrical issue and diagnose it before touching the mechanical side.
- You inherited a gate with no records. No manual, no wiring diagram, no idea what brand the operator is. We identify the equipment, document it, and leave you a written record so the next technician doesn’t have to start from zero.
Our Driveway Gate Process

Every driveway gate job follows the same documented sequence. No step gets skipped, and you see the paperwork at each stage.
- Site walk and measurement. We measure the opening, check the grade, confirm power availability, and note the swing or slide clearance. On a sloped Winchester driveway this matters more than the gate itself, because the operator has to move the gate’s weight against gravity on every cycle.
- Written scope and written price. Before a single tool comes out, you get the flat price in writing. Parts are itemized by brand and model. If we find something mid-job that changes the scope, you get a revised written price before we continue, never a surprise invoice at the end.
- Identification and documentation of existing equipment. If there’s an operator already on the property, we identify the brand (Elite, FAAC, LiftMaster, and the other major lines we service), photograph the control board, and record the wiring before we change anything.
- Installation or repair. Gate hung, hinges set, operator mounted, arm or chain aligned, and safety devices positioned. For new installs we set the open and close limits by degrees so the gate stops where it should, not where it happens to land.
- Safety testing. Photo-eyes, edge sensors, and the obstruction-reversal function get tested and documented. This is the part most homeowners never see, and it’s the part that matters most.
- Photo record and handoff. You get a photo log of every adjustment and a written record of the part numbers installed. It’s filed in the job record too, so if you call us in two years the history is already there.
The whole job is covered by our 365-Day Done Right Promise: if the repair isn’t right, we make it right at no additional charge within that year. No argument, no fee.
Before
AfterDriveway Gate Pricing in Winchester
Driveway gate pricing in Winchester depends mostly on whether you’re installing new or repairing existing, and on the weight and width of the gate the operator has to move. Here are the ranges we see on residential properties, written in dollars so you can plan before you call:
| Job | Typical range | What moves the price |
|---|---|---|
| Single-swing operator replacement (LiftMaster, Elite class) | $850 – $1,400 | Brand, arm bracket condition, whether control wiring is reusable |
| Dual-swing operator replacement | $1,500 – $2,600 | Two arms, synchronized control board, safety-device count |
| Slide-gate operator replacement | $1,200 – $2,200 | Gate weight, rack condition, chain vs. rack-and-pinion drive |
| New gate hung on existing posts (manual) | $900 – $2,000 | Gate width, material, hinge and latch hardware |
| New automated driveway gate (gate + operator) | $2,800 – $6,500 | Span, material, power run distance, operator brand |
| Photo-eye realignment or replacement | $120 – $260 | Whether the bracket or the sensor itself failed |
| Limit switch reset or replacement | $140 – $300 | Access to the switch housing, board type |
| Hinge or bracket weld repair | $180 – $450 | Whether the post or the gate frame needs work |
Two things drive cost up on Winchester properties more than anywhere else: power-run distance (if the operator has to be fed from a panel on the far side of the house, that’s conduit and trenching) and gate weight (a heavy ornamental iron gate needs a heavier-duty operator than a lighter aluminum one of the same span). We don’t quote a range and then hand you a different number at the end. The written price is the price, and it’s in your hands before work starts.
If you’ve already got a written estimate from another company and something in it doesn’t add up, bring it to us. We’ll review it at no cost and tell you what we’d do differently, if anything. That second opinion is free and there’s no obligation.
What brands do you work on?
We service nine major gate-automation brands, including LiftMaster, FAAC, Elite, and Mighty Mule, along with BFT, Linear, Viking, Ghost Controls, and DoorKing. That range means you don’t have to replace a working operator just because a different company only stocks one brand. We work with what’s on your property first and recommend replacement only when repair genuinely isn’t the better call. Call (866) 983-9213 with the brand name and model if you have it, and we can often tell you what to expect before we arrive.
FAQs – Driveway Gate

How much does a driveway gate cost in Winchester, NV?
Most residential driveway gate repairs in Winchester run $120 to $450, while a full new automated gate installation typically lands between $2,800 and $6,500 depending on span, material and operator brand. The single biggest cost factor is whether you’re repairing an existing operator or installing new, followed by gate weight and power-run distance. We put the exact flat price in writing before any work begins, so you’re never guessing. Call (866) 983-9213 for a free estimate.
Can you repair my gate the same day?
Many common driveway gate problems, including photo-eye misalignment, limit-switch faults and hinge adjustments, can often be handled the same day you call, depending on parts availability for your operator brand. A live person answers our phone 24 hours a day, seven days a week, so you’re never routed to voicemail or a callback queue. Call (866) 983-9213 and we’ll tell you honestly what’s realistic for your gate.
Is it cheaper to repair or replace a driveway gate operator?
Repair is usually the cheaper path when the motor, control board and drive mechanism are still sound and the fault is a sensor, limit switch, or bracket. Replacement makes more sense when the control board has failed on an operator that’s already been repaired more than once, or when the drive gear is stripped beyond service. We diagnose first and show you the photo evidence, then let you decide with a written price for each option in hand. Call (866) 983-9213 to book a diagnosis.
Do you work on gates with no manual or records?
Yes. We identify the operator brand and model, photograph the control board, and record the existing wiring before touching anything, so an undocumented gate becomes a documented one by the time we leave. That record stays in the job file and a copy goes to you. Call (866) 983-9213 and describe what you’re looking at, and we’ll take it from there.
What is the 365-Day Done Right Promise?
It’s our written guarantee that if a repair isn’t right, we make it right at no additional charge within one full year of the work, with no argument and no fee. It applies to every driveway gate job we complete, and it’s part of The Haven Standard that governs all our work. Call (866) 983-9213 if you have questions about coverage on a specific job.
How long does a driveway gate install take?
A straightforward single-swing operator replacement is often a half-day job, while a full new automated driveway gate with a fresh power run can take one to two days depending on trenching and concrete set time. We give you a realistic time window in the written scope so you can plan around it. Call (866) 983-9213 to schedule a site walk and get your written price.
If your driveway gate is sticking, reversing, dragging, or you’re ready to automate an entrance that’s never had a motor, call (866) 983-9213 for a free estimate. A live person will answer, we’ll put the price in writing before anything starts, and you’ll have a photo record in hand when we leave. Vance Gate Repair Winchester serves homeowners across the Winchester area with the same documented approach on every driveway gate, swing or slide, new or existing.
Written by the team at Vance Gate Repair Winchester, serving Winchester.