Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Winchester Homeowners
A gate that won’t open is a car trapped in a driveway. A gate that won’t close is worse: the whole property is open until someone fixes it. We handle both, often the same day, and we hand you a written price before a single tool comes out of the case. Our technicians bring up to 12 years of experience to every call, and we’ve completed more than 22,000 gate repairs and installations since 2014. Same-day service is available across Winchester, and a live person answers at (866) 983-9213 at any hour. No voicemail loop, no callback queue.

Winchester sits in the middle of the valley, and that matters for gates. The heat here works on steel and wiring the same way it works on everything else. Sun-exposed operators in this part of town run hotter than the spec sheets assume, and we see the results regularly: control boards that fail in July, plastic limit-switch cams that go brittle, hinges that seize because the grease cooked off two summers back. Repairing a gate in Winchester means knowing which of those failure modes you’re looking at before you quote anything.
Key Takeaways
- Written flat price handed over before work starts, on every job (Haven Standard Clause 1).
- 365-Day Done Right Promise: if a repair isn’t right, we make it right at no additional charge within that window.
- Nine major automation brands serviced, including FAAC, Elite, LiftMaster and Mighty Mule.
- Every visit ends with a documented photo record of what we found, adjusted and replaced.
- A live person answers the phone 24 hours a day, seven days a week.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
What Our Gate Repair Service Includes

Gate repair isn’t one skill. A driveway gate has a mechanical half, an electrical half and a structural half, and they fail in different ways. Here’s what each part of the job covers.
Electric Gate Repair
Electric gate repair covers everything on the power side of the operator: the control board, the transformer, the wiring run, the photo-eye pair, the safety loop in the driveway and the battery backup. You need it when the gate stops responding to a remote, cycles on its own, or blows a fuse the moment you restore power. We meter the circuit at each junction and photograph the readings, so the next technician (or you, three years from now) can see exactly what the voltage looked like on the day of the repair.
Automatic Gate Repair
Automatic gate repair is the control-and-travel side: limit switches, encoder counts, obstruction sensitivity, opening and closing speeds and the logic that decides when to reverse. You need it when the gate over-travels, slams into the stop, reverses halfway through a cycle or refuses to open past a certain point. We read the limit positions, set them to spec and record the new values. A limit switch set 12 degrees past travel will trip a safety input eventually, and that’s the kind of thing we fix on the first visit rather than the third.
Hinge & Post Repair
Hinges and posts carry the whole weight of a swing gate, and the valley climate is hard on both. You need this work when a gate sags on one corner, drags on the driveway, or a post has started to lean or show a crack at the weld collar. We check plumb on the post, verify the hinge barrels aren’t ovalized, and repair or reset what’s actually moving. Replacing a hinge that wasn’t the problem only hides a failing post for another season.
Gate Realignment
Realignment is exactly what it sounds like: bringing the gate back to true against the post and the strike, so it latches cleanly without lifting or dragging. You need it after a vehicle bump, a wind event, ground movement, or a hinge repair that shifted the geometry slightly. We measure the gap at the top, middle and bottom of the strike side, then correct the hinge side first. Realigning the latch without fixing the sag generally doesn’t hold past a month.
Lock Repair
Lock repair covers the mechanical latch, the magnetic lock, the keypad or card reader that releases it, and the strike plate that has to line up for any of it to work. You need it when the gate closes but doesn’t latch, when the keypad accepts a code and nothing happens, or when the mag lock buzzes but won’t release. We test the lock under load, not just by hand, because a mag lock holding at 60 pounds when it should hold 600 is a security problem disguised as a working gate.
Weld & Rust Repair
Weld and rust repair handles the structural joints: hinge plates, post collars, frame corners, bottom rails that have rusted through. You need it when you can see rust bleeding from a seam, when a weld has cracked at the toe, or when the bottom of the gate has started to flake. We grind back to sound metal, weld, and treat the area so it doesn’t come back next monsoon season. Painting over rust is a one-summer fix; we’d rather do the job once.
Before
AfterBrands We Service for Gate Repair
We work on whatever operator is already on the property. That’s a deliberate choice. When a homeowner calls about a FAAC swing operator that won’t close, the useful answer is a repair on the FAAC, not a pitch to swap the whole assembly. We know where FAAC 400-series arms wear at the pivot bushing, and we know how their encoder feedback behaves when the gearbox is on its way out. On LiftMaster slide and swing operators, we’ve seen enough of the control boards to recognize the difference between a failed board and a board that’s fine but getting bad input from a photo-eye.
Elite and Mighty Mule round out the residential side. Elite operators tend to last well but their limit cams go out of adjustment over time, and we reset those to spec and photograph the new position. Mighty Mule is common on lighter residential gates, and we know its weak points: battery terminals that corrode, control boards that don’t tolerate a weak battery, and arms that need a bracket check before anything else gets blamed. Whether you have FAAC, Elite, LiftMaster or any other make, we can help.
Signs You Need Gate Repair Right Now

Some gate problems can wait a week. Others put the property at risk tonight. Here’s how to tell them apart.

- The gate reverses without anything in the path. An obstruction sensor that trips on nothing is usually a misaligned photo-eye or a failing safety edge. It will get worse, and a gate that reverses unpredictably can catch a vehicle or a person mid-cycle.
- You can hear the motor run but the gate doesn’t move. That’s a mechanical disconnect: a sheared arm pin, a stripped gear, a chain that’s come off its sprocket. Running the motor in that state can damage the gearbox, so stop cycling it and get it looked at.
- The gate sags visibly or drags on the ground. This is hinge and post territory. A drag that starts small will wear the operator out within weeks, because the motor is now lifting weight it was never sized for.
- Rust is bleeding from a seam or weld. Surface rust on paint is cosmetic. Rust coming out of a joint means the metal inside is going, and a structural weld that fails under load drops the gate.
- The gate won’t latch or the lock won’t release. A gate that closes but doesn’t lock is open, regardless of what it looks like from the street. Mag locks and strikes that half-work tend to fail fully at the worst possible moment.
Our Gate Repair Process – Step by Step
- 1
We answer the phone and ask what the gate is doing. A live person takes the call at any hour, and the first questions are about symptoms, not sales. Does it move at all? Does the motor run? Did it stop after a specific event like a bump or a windstorm? That conversation tells us what to bring.
- 2
We come out and diagnose before we quote. On site, we meter the electrical side, check the mechanical travel and inspect the structure. On a swing gate that means checking post plumb with a level and reading the limit positions. On a slide gate it means checking the track, the rollers and the chain tension. Every reading gets photographed.
- 3
You get the flat price in writing before any work starts. The written scope names what we found, what we’ll do about it, and the price. Nothing is added later that wasn’t on the page. If the diagnosis changes mid-job, we stop and re-quote rather than finishing and surprising you.
- 4
We do the repair and document it. When we’re done, you get a photo log: the failed component, the new part number, the limit-switch readings, the photo-eye alignment. It goes in the job record and a copy stays with you. If another company ever quotes this gate again, the paperwork is already there.
- 5
We test under real conditions before we leave. That means a full open and close cycle, an obstruction test with an actual object in the path, and a battery-backup check where one is fitted. Then we walk you through what we found and what we changed. Under Clause 4 of the Haven Standard, the photo record is included on every visit at no extra charge.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Winchester?

Most gate repairs in Winchester land between $185 and $650, and the written price is agreed before work begins. Here’s roughly how the common jobs break down:
| Repair | Typical range | What drives the number |
|---|---|---|
| Photo-eye or safety edge repair | $185 – $320 | Whether the eye is misaligned or the receiver has failed |
| Limit switch reset or replacement | $195 – $340 | Setting-only versus a new switch and cam |
| Hinge replacement and rehang | $240 – $480 | Number of hinges, gate weight, post condition |
| Gate realignment | $220 – $400 | Whether the post has moved or only the hinge side |
| Lock, strike or mag-lock repair | $210 – $520 | Mechanical versus powered lock, keypad involvement |
| Weld and rust repair | $280 – $650 | Extent of the section, access, finish work after welding |
| Control board replacement | $380 – $700 | Brand and board availability |
What moves the price most is access and condition. A gate that’s been dragging for six months costs more to fix than one that started dragging last week, because the operator has usually taken damage by then. That’s also the most common way homeowners overpay: paying for a motor replacement when the real problem was a $40 hinge. Our estimate is free and the findings get documented, so you can see the actual cause before you spend anything. If you’ve already got a written estimate from another company, bring it and we’ll review it at no cost as a second opinion.
Gate Repair Near Winchester – Our Service Area
We cover Winchester and the surrounding valley, including Paradise, Sunrise Manor, Whitney, Spring Valley, Enterprise, Las Vegas and North Las Vegas. Response times depend on the day and the traffic on the 95, but most Winchester calls get same-day attention when you reach us in the morning. If you’re further out toward Henderson or Boulder City, we’ll give you a straight time window on the phone rather than a vague promise. For nearby neighborhoods, see our Gate Repair in Paradise page.
Serving Winchester, NV – Our Local Coverage Area

We serve Winchester and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Repair in Winchester
Gate repair is the diagnosis and correction of a gate that isn’t opening, closing, latching or holding correctly. It covers the mechanical side (hinges, posts, frames, welds), the electrical side (control boards, wiring, photo-eyes, locks) and the automation side (limit switches, travel settings, safety inputs). At Vance Gate Repair Winchester, every repair starts with a diagnosis and a written price, not an estimate over the phone.
Most single-issue repairs finish in one visit of one to three hours. A photo-eye realignment is typically under an hour; a hinge replacement with a rehang runs two to three hours; weld and rust repair on a structural joint can take longer because the finish has to cure. If the job needs a part we don’t have on hand, we’ll tell you the lead time in writing before you commit. Call (866) 983-9213 for a realistic window on your specific gate.
Most repairs run $185 to $650, with control board replacement at the top end and sensor or limit-switch work at the bottom. The flat price is written and agreed before any work starts, so the invoice matches the quote. Factors include the brand of operator, whether the gate has been dragging, and how accessible the operator housing is on your property. Call (866) 983-9213 for an exact quote; estimates are free.
Yes, along with Elite, Mighty Mule, BFT, Linear, Viking, Ghost Controls and DoorKing. That’s nine major automation brands, and the point is that we work on the operator already on your property rather than steering you toward a replacement. If your gate has a brand we haven’t listed, call and describe it; most residential operators are straightforward to diagnose once we know the model.
In most cases, yes. A live person answers the phone 24 hours a day, seven days a week, so you’re never routed to voicemail or a callback queue. Same-day service is available across Winchester and nearby areas, and if the gate is stuck open on a property, we treat it as a priority. Call (866) 983-9213 and we’ll tell you honestly what’s possible today.
Yes. Every completed repair is covered by our 365-Day Done Right Promise: if the repair isn’t right, we come back and make it right at no additional charge within that window. There’s no fee to invoke it and no argument attached. The documentation from your visit is what makes that promise workable, because we can see exactly what was found and set on the original job.
Clear the driveway on both sides of the gate so the technician can cycle it fully without moving vehicles, and make sure someone is home to open the operator housing or gate box if it’s locked. If you have a remote that stopped working, leave it out. If another company has already given you a written estimate, have that paperwork ready; we’ll review it free of charge as a second opinion. Call (866) 983-9213 to schedule.
Schedule Your Gate Repair Service in Winchester Today

If your gate is stuck, dragging, not latching or cycling on its own, call (866) 983-9213. A live person answers at any hour, we’ll give you a written flat price before any work starts, and every visit ends with a documented photo record of what we found and what we left behind. Estimates are free and there’s no obligation. Start with our home page or go straight to Gate Repair in Winchester for the full service breakdown.
Written by the team at Vance Gate Repair Winchester.