A Vance company - serving Winchester, NV

Before & After Gallery - Vance Gate Repair Winchester

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Gate Repair Before & After in Winchester, NV

Seeing the work speaks louder than any claim we could make. Below are before-and-after write-ups from gate repair jobs around Winchester: what we found, what we adjusted, and what the gate did afterward. Each one follows the same routine – written price agreed first, photo record taken before and after, and a full year to make it right under the 365-Day Done Right Promise.

Call (866) 983-9213

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Recent Transformations

Swing Gate That Stopped Reversing – FAAC Operator Reset in a Sun City Anthem Courtyard

BeforeBeforeAfterAfter
Before – FAAC swing gate arm hitting the closed stop, with the post scuffed from repeated contact.
BeforeBeforeAfterAfter
After – limit switch reset and photographed; the arm now stops and reverses evenly.

This FAAC swing gate in a Sun City Anthem courtyard kept striking its closed stop, and the homeowner was worried the safety reverse was failing. We checked the photo-eyes first and found the beam misaligned by about two inches after the low winter sun shifted across the driveway. We realigned the mounts, then found the limit switch set past the gate’s true travel – the arm was driving into the hard stop on every close. We reset the limit and re-ran the reverse test with a box in the path. The gate now reverses cleanly on contact, and the homeowner has a photo log of the new switch position.

Sliding Gate That Wouldn’t Close – Roller and Track Repair in Green Valley

BeforeBeforeAfterAfter
Before – seized ground roller and a track that had drifted out of true.
professional gate repair service
After – new rollers and a trued track; the gate now glides level and latches the first time.

This sliding gate in Green Valley would travel about halfway and then stall, and the homeowner had been propping it with a patio chair. The track had drifted out of true, and one ground roller had seized from grit that builds up through the dry months around Winchester. We replaced the failed roller set and realigned the track back to level. A gate this heavy was dragging on the operator and had started to chew its own motor; fixing the rail first meant the operator didn’t need replacing. We left a photo of every adjustment and the part numbers fitted.

LiftMaster Opener Caught by Power Surges – Surge and Control Board Replacement in Summerlin

Professional welder performing gate hinge repair and metal fabrication services.
Before – the board had taken a surge; the gate was stuck and the operator would not respond.
A professional repairing a cracked decorative metal gate post with epoxy
After – new control board and a surge module; the operator cycles normally again.

A LiftMaster operator on a Summerlin property had gone dead after a thunderstorm, and the homeowner assumed the whole unit had failed. We opened the housing and traced the fault to a scorched control board – a common outcome when a nearby strike pushes voltage through a gate motor in Winchester’s storm season. We replaced the board rather than the operator, added a surge protection module ahead of it, and tested the full cycle. The gate is running again for a fraction of what a replacement would have cost.

Ghost Controls Opener That Wouldn’t Take the Remote – Receiver and Antenna Fix in Centennial Hills

Two professional technicians installing a custom wrought iron driveway gate
Before – antenna connection corroded from fine desert dust and summer heat.
professional gate installation service
After – connection cleaned and remotes re-paired and tested.

The homeowner in Centennial Hills had bought new remotes because theirs had “stopped working,” and the new ones wouldn’t pair either. The real fault was a corroded antenna connection on the Ghost Controls receiver – fine dust and heat had worked at the fitting until the signal dropped. We cleaned and reseated the mount, re-paired the existing remotes, and confirmed range from the far end of the driveway. The old remotes still work. We always check the receiver before a customer spends money on parts they may not need.

Wrought-Iron Gate Sagging on Its Hinge – Welding Repair in the Lakes

Two technicians installing a new custom metal gate between block walls.
Before – the lower hinge weld had cracked and the gate was dragging the ground.
Technician troubleshooting an automatic sliding gate motor with a multimeter
After – hinge rewelded, gate squared, and the repair painted to match.

A wrought-iron pedestrian gate at a Lakes property had dropped until it dragged on the ground, and the cracked weld at the lower hinge had started to split wider. We realigned the hinge, welded the joint back solid, and dressed the repair so it disappears against the frame. The gate swings square and latches the first time. Welding is where we prefer repair – there’s rarely a reason to replace good iron because one joint failed.

Gate Opener That Kept Running at Night – BFT Limit and Timer Set in Peccole Ranch

Technician performing professional gate motor and opener repair service
Before – timer and limit settings letting the operator run long after the gate had closed.
professional gate motor & opener service
After – timer corrected and cycle tested; the gate now stops where it should.

This BFT operator in Peccole Ranch was cycling on its own at night, and the homeowner had started unplugging it before bed. We traced it to a timer setting left open after a prior adjustment and a limit set just short of true travel, which made the operator keep trying to close a gate that was already shut. We corrected both settings and ran a full open-close test. It’s been quiet overnight since. Every setting change went on the photo record.

Want Results Like These?

professional gate repair service
Want Results Like These?

If your gate is dragging, stalling, cycling on its own, or hitting its stops, call us at (866) 983-9213. We’ll bring the right parts, write the price before any work begins, and leave a photo record of everything we adjusted. Licensed and insured, with the 365-Day Done Right Promise standing behind every repair in Winchester.

Written by the team at Vance Gate Repair Winchester.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need Gate Repair help in Winchester? Licensed & insured · 30-60 min response · free estimates
Call (866) 983-9213
Local Service Coverage

Request a Free Estimate in Winchester

Tell us what you need - Vance Gate Repair Winchester responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Send a Text
Call Now - 24/7 Dispatch