A Vance company - serving Winchester, NV

Ghost Controls Welding & Fabrication in Winchester, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Welding & Fabrication: The Winchester Owner’s Guide

We repair and re-fabricate Ghost Controls gate hardware in Winchester, including welded hinge brackets, post plates, arm mounts, and gate frames cracked or rusted past the point where bolts alone will hold. Most welding and fabrication work on a Ghost Controls residential gate in Winchester runs $280 to $650 installed, depending on whether the damaged piece is a bracket we can repair in place or a frame section that has to be cut out and re-welded. This is scheduled work, not same-day emergency service: we measure, order or fabricate the piece, then return with a written price before anything is cut.

Call (866) 983-9213

Owners usually find the problem in one of two ways. Either the gate sags and drags on the driveway no matter how many times the operator is reset, or the automatic open stops halfway and the arm looks like it’s fighting something. Both point back to the same thing: the welded steel the Ghost Controls arm pushes against has given way. (Ghost Controls builds its own operators; we’re an independent shop and not affiliated with the brand.) In Winchester, we see it most on gates facing full afternoon sun with a hinge plate welded years ago and never re-checked.

Key Takeaways

  • Welding and fabrication for Ghost Controls gates in Winchester typically runs $280 to $650 installed.
  • Most failures are cracked hinge brackets, wall plates, or arm mounts, not the operator itself.
  • We’re an independent service provider, not affiliated with Ghost Controls.
  • The written price is handed over before any cutting or welding starts.

Which Ghost Controls Models This Applies To

Ghost Controls makes single and dual swing-gate operators, and the welded steel that matters is the same across basically all of them. If your gate has a Ghost Controls operator mounted on it, this page applies. The arm, the control box, and the safety edges mount to specific steel points: the gate frame, the hinge post, and the wall or post plate the actuator anchors to. Those anchor points are where welding and fabrication work lives, regardless of model.

To identify what you actually have, look in two places. First, the operator arm or the housing usually carries a label with the model family printed on it, and the control box does too. Second, measure the gate leaf width and the post spacing before you buy or order any bracket. A bracket welded for a 12-foot single leaf and one built for a 6-foot leaf are not interchangeable, and the arm mount angle changes with leaf length. That measurement is the single most common mistake we correct in Winchester, and it’s cheap to check and expensive to get wrong.

On the OEM-versus-aftermarket question for Ghost Controls specifically: for the operator itself, Ghost Controls parts are the right call, since fit and warranty travel together. For the welded steel underneath it, a fabricated bracket sized to your gate is usually better than a stock replacement, because it’s made for your hinge post and your leaf, not for a generic frame. We fabricate to fit, then photograph the installation so the next person has a record.

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Signs Your Ghost Controls Welding & Fabrication Is Failing

professional gate repair service
Signs Your Ghost Controls Welding & Fabrication Is Failing
  • The gate sags and drags. A cracked or fatigued hinge weld lets the leaf drop a fraction of an inch, which grows over months. Drag marks on the driveway are the tell.
  • The operator strains or stalls partway. When the arm mount or post plate flexes, the operator is pushing against a moving anchor. It reads as a motor problem, but the steel is the cause.
  • Visible rust bloom or paint lifting at a weld. A weld that failed its corrosion seal rusts from the inside out. Bubbling paint at a joint means the weld is going.
  • The gate hangs crooked, or the hinge gap changes with the weather. A widening gap at one hinge and a tight one at the other says the weld has shifted, not that the gate is settling.
  • A wobble you can feel by hand when the operator is off. With the gate in manual, grasp the leaf and rock it. Any clunk at the hinge or post plate is steel fatigue.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
BeforeBefore
AfterAfter

Replacement Cost & What’s Included

Here’s the range for welding and fabrication work on a Ghost Controls gate in Winchester:

  • Hinge bracket repair or re-weld (in place): $280 to $420
  • Wall plate or post plate replacement, fabricated to fit: $350 to $520
  • Gate frame section cut out and re-welded: $480 to $650
  • Operator arm mount re-fabrication and re-hang: $400 to $600
  • Corrosion seal and repaint on a finished weld: $80 to $160
  • The price depends on three things: whether we can reach the weld in place or have to pull the gate, how much of the frame has to be cut out, and whether the operator arm has to come off for access. Every quote breaks out the fabricated piece, the welding, the corrosion seal, and any hardware at line-item prices before work starts. That’s the whole point of Clause 1: you see the number and agree to it. The 365-Day Done Right Promise covers the weld, and if it fails within a year we fix it at no charge.

    DIY or Call Us?

    Professional welder performing gate hinge repair and metal fabrication services.
    DIY or Call Us?

    Some of this you can safely check. Rock the gate with the operator off and listen for a clunk. Look for rust bloom and paint lifting at any weld. Measure your leaf width and note the model label on the arm. Those checks tell us a lot before anyone arrives, and none of them put you near a hot torch or a hydraulic arm under load.

    What we don’t want you doing is welding, cutting, or re-mounting the operator anchor yourself unless you’re trained. Gate steel under tension moves when you cut it, an operator arm can swing free, and a weld that isn’t rated for the load can let a gate fail suddenly. That’s how people get hurt, and it’s also how a $300 bracket repair becomes a $900 frame job. If you’re unsure, call us at (866) 983-9213 and describe what you’re seeing. We’ll tell you honestly whether it’s a check or a repair.

    Get the price in writing before anything starts.A real person answers, day or night.
    Call now

    FAQs

    Need Gate Repair help nationwide? Licensed & insured · 30-60 min response · free estimates
    Call (866) 983-9213
    Local Service Coverage

    Request a Free Estimate in Winchester

    Tell us what you need - Vance Gate Repair Winchester responds fast. No obligation.

    By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

    Prefer to text? Send a Text
    Call Now - 24/7 Dispatch