Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor Replacement: The Winchester Owner’s Guide
We replace Ghost Controls gate motors in Winchester with the correct compatible unit for your series, and most installed replacements run $425 to $780 depending on model, arm condition and whether the control board survives. We can usually get a failing motor swapped the same day you call. Homeowners in Winchester tend to find us the same way: the gate gets slower, then it stops short of full travel, then it won’t reverse off the post at all. By the time the motor clicks and does nothing, most people have already reseated the battery backup and reset the breaker twice. A Ghost Controls operator that stalls under load is almost always a motor or control board problem, not a mystery. We confirm which one before we quote a replacement, because a $500 motor you didn’t need is a bad day for everyone.
Which Ghost Controls Models This Applies To
Ghost Controls builds single and dual swing-gate operators in the AXO, AXD, TSS and TDS family lines, plus the newer controller-style units. The model plate is on the underside of the control box or stamped on the motor housing, and it carries the series and the date code. Read that plate before you shop for a part. The compatibility gotcha that catches most Winchester owners: the gear housing and drive-arm mount changed between older TSS units and current production, so a current motor won’t bolt onto an older bracket without the matching arm kit. Measure the arm’s overall length and the distance between the mounting holes before ordering anything. On the OEM-versus-aftermarket question, Ghost Controls’ own replacement motors carry the correct gear ratio and connector pinout. Aftermarket motors for these units exist and some are fine, but the armature and limit-switch tolerances vary, and a cheap motor with the wrong gear ratio will run your gate past its stops within a week. We give you the verified part number in writing either way.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Gate Motor Replacement Is Failing

- The gate moves slowly or hesitates mid-travel. Usually a worn motor brush or a failing capacitor, not a battery issue. A Ghost Controls operator in Winchester’s summer heat loses capacitor capacity faster than the manufacturer’s lifespan chart suggests.
- The gate stops and reverses partway open or closed. The control board is reading an obstruction that isn’t there. Often a current-sensing fault on the board itself, sometimes a stuck limit switch sending a false end-of-travel signal.
- You hear a click at the motor and no movement. The board is firing the relay but the motor isn’t turning. Brushes worn to the limit or a seized gearbox. This is the point where replacement beats repair in most cases.
- The arm separates from the gate or wobbles at the bracket. A stripped mounting bracket or worn bushing, aggravated by the differential thermal expansion of desert heat. Left alone, the loose arm torques the motor shaft and takes the gearbox with it.
- Battery backup runs minutes, not cycles. In an older unit the battery may be fine but the charging circuit on the control board has failed, so the battery never fully recovers. We test the charging output before recommending a battery versus a board versus a motor.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Winchester, a Ghost Controls gate motor replacement typically lands between $425 and $780 installed, and the price is written and handed to you before any work starts. Here’s what sits behind that range.
| Item | Typical range |
|---|---|
| Replacement motor (OEM-compatible) | $220 – $410 |
| Control board, if diagnosis calls for it | $130 – $240 |
| Arm bracket or gear-housing kit (model-dependent) | $45 – $120 |
| Labor and re-tuning | $120 – $200 |
The range moves with model series, whether the arm bracket is intact, and whether the limit switches carry over or need resetting. We document the failing part with photos, show you the reading that proves it, and leave a record of the part number installed. Every completed replacement carries our 365-Day Done Right Promise: if it isn’t right within a year, we make it right at no additional charge.
DIY or Call Us?

You can safely check a few things yourself: read the model plate, look for corrosion on the battery terminals, confirm the breaker and the wall switch are on, and clear any obstruction from the beam path. Where DIY goes wrong on a Ghost Controls motor is the electrical side and the post-install tuning. The motor runs on 12 or 24 volts DC from a transformer, and swapping the unit means disconnecting and reconnecting live low-voltage feeds at the control box, then resetting the limit switches and the obstruction-sensing force. Set the force too high and the gate won’t stop for a child or a pet. Set the limits wrong and the motor drives into the post and strips the gearbox you just paid for. That’s the part we’d rather you didn’t gamble on. Call (866) 983-9213 and we’ll come out, confirm the diagnosis, and quote the swap in writing before we touch a wire. We’re an independent service provider, not affiliated with Ghost Controls, but we work on their operators every week.
FAQs
A Ghost Controls motor in Winchester typically lasts 6 to 10 years, and the low end is more common on gates that cycle heavily and sit in full afternoon sun. Desert heat and summer dust work on the brushes and gearbox, so a unit running 20-plus cycles a day ages faster than the manufacturer’s duty rating suggests. If yours is past that window and stalling under load, the motor is a likely culprit. Call (866) 983-9213 for an exact diagnosis and a written price – estimates are free.
Sometimes, yes, and we’ll tell you honestly which parts are still worth repairing. A failed control board or a bad limit switch can usually be replaced on its own for less than a full motor swap. A worn brush set can be rebuilt on some units. A stripped gearbox or a seized armature means the whole operator gets replaced, because those internals aren’t sold separately. We test each component before recommending either path. Call (866) 983-9213 and we’ll give you the written price for both options.
A single-gate motor replacement usually takes about 90 minutes to two hours once the correct part is on-site, and a dual-gate setup takes longer. The time goes to mounting, reconnecting the low-voltage feeds, and re-tuning the limit switches and force sensing so the gate stops exactly where it should. If the arm bracket needs replacing or the control board is also failing, add 30 to 45 minutes. Call (866) 983-9213 to schedule and we’ll confirm timing and price upfront.
We match the part to the model series and date code on your Ghost Controls operator, not to a guess, and we give you the verified part number in writing before we order. We don’t carry stock in a warehouse or on a truck; we source the correct motor for your specific unit and schedule the install around its arrival. That’s why the price on your quote is the price you pay. We also service LiftMaster, Mighty Mule and DoorKing operators for Winchester homeowners who have a different motor on the property. Call (866) 983-9213 for a free estimate.
When your Ghost Controls gate stops short, clicks without moving, or drives past its stops, the fastest path to a working gate is a call to (866) 983-9213. We diagnose the failing part, hand you a written flat price before any work begins, and leave a photo record of what we found and what we installed. Estimates are free, and a live person answers the phone at any hour.
Written by the team at Vance Gate Repair Winchester, serving Winchester and nearby areas.